All Questions
11
questions
0
votes
0
answers
28
views
PFsense: fake subnet
I have got on IPSec tunnel mapping a remote 172.x/24 network to my local 10.x/16 network.
Because I cannot change the configuration on the remote site I need to use this like this (with 10.x/16 ...
- 73
0
votes
1
answer
208
views
IpSec StrongSwan HA config misses / no connection
I am using strongswan on rasberian 12 to connect to PFsense with /etc/ipsec.conf from an external network to an PfSense:
config setup
conn %default
keyexchange=ikev1
conn peer-ipsec.xxx.de-...
- 73
0
votes
0
answers
141
views
IPSEC libreswan interface endpoint does not match left or right
I am using libreswan on raspberry Pi OS 12 to connect to PFsense with /etc/ipsec.conf
from an external network
config setup
conn %default
#keyexchange=ikev1
conn peer-ipsec.xxx.de-tunnel-1
...
- 73
1
vote
0
answers
65
views
IPSec Phase 2 Configuration For Translated Subnets?
I have two networks with the 10.0.0.0/8 subnet I'm trying to connect via IPSec tunnels. I have the phase 1 configurations working but am a bit stuck on the phase 2 configurations. Each firewall used ...
- 314
0
votes
1
answer
3k
views
How can I create an IPsec tunnel between a FritzBox and a pfsense, without using Aggressive Mode?
I've successfully created an IPSEC Tunnel between my local FritzBox 7590 and my office, which is running a pfsense hardware firewall (APU2) with pfsense 2.4.5-RELEASE-p1 and coreboot firmware v4.11.0....
- 151
1
vote
0
answers
3k
views
How to setup IPSec VPN between PFSense and Edgerouter X
We have 2 routers/firewalls, 1x pfSense and 1x UBNT Edgerouter X. I tried to setup an IPsec site-to-site connection between these 2 but i cannot get it done. I followed multiple "tutorials"/...
- 133
1
vote
0
answers
131
views
How to configure pfsense to use VPN as gateway for OPT port only?
Currently I have set up my PfSense SG-1100 to function as a site to site VPN. I have an unused OPT port on my router and I want to attach that to a switch and have it function as the gateway to the ...
- 11
0
votes
1
answer
10k
views
IPsec on pfSense: Tunnel is up, but I can't connect to remote host
I have a strange problem with my IPsec VPN:
I have 2 matched [hardware and software - 2.4.4 release p3] pfSense boxes at different locations.
Each pfSense is a Firewall + DHCP server + Gateway for the ...
0
votes
1
answer
7k
views
PFSense IPSec connection established, wan works, lan not
I want to setup a vpn service on top of my PFSense box at home. PFSense is configured and working fine for my home network.
The problem is, that i can only access wan addresses over the vpn tunnel ...
1
vote
2
answers
7k
views
Have Site-To-Site (IPSEC) connected but cannot ping anything other than router
Just setup a new Azure subscription, and i'm stumped trying to troubleshoot why I can't ping any local VMWare machines from a Azure VM. After successfully setting up an IPSec Site-To-Site VPN.
I am ...
1
vote
0
answers
1k
views
PFsense OpenVPN traffic getting routed through WAN rather than IPsec tunnel
So I have a PFsense firewall setup with a IPsec tunnel created to access a special webpage housed at another companies website. Internal traffic routes properly through the IPsec tunnel for this ...
- 11